Công Ty Tăng Minh Phát - Đại lý Fireye Việt Nam, chuyên cung cấp thiết bị phát hiện ngọn lửa, cảm biến ngọn lửa, máy phát hiện lửa, máy quét ngọn lửa, thiết bị phát hiện ngọn lửa bằn tia hồng ngoại, thiết bị phát hiện ngọn lửa bằng tia cực tím ( tia UV)...của hãng Fireye tại Việt Nam

Thiết bị phát hiện ngọn lửa ( cảm biến ngọn lửa) : dùng phát phát hiện những nơi có nhiệt độ nóng bất thường, nguy cơ xảy ra cháy nổ cao, để giảm bớt rủi ro không mong muốn trong quá trình hoạt động của các nhà máy.

4 loại cảm biến ngọn lửa thông dụng : cảm biến phát hiện ngọn lửa bằng tia hồng ngoại, cảm biến phát hiện ngọn lửa bằng tia cực tím, cảm biến ngọn lửa dạng IR, cảm biến ngọn lửa dạng IR3

Thiết bị phát hiện ngọn lửa Fireye | Cảm biến phát hiện ngọn lửa Fireye | Máy quét ngọn lửa Fireye

Thiết bị phát hiện ngọn lửa 105F1-1 Fireye (105F1-1 Flame Scanner)

The Fireye^® Paragon™, type 105F1-1 flame scanner is a microprocessor based flame analysis device utilizing solid state flame detection sensors.

The Paragon scanner provides high integrity sensing of multiple flame properties, including Amplitude, Flicker Frequency and Flame Learned vs. Stored Curve Fitting. Combinations of these measured properties are utilized to provide superb discrimination in a multiple burner, multi flame application as well as monitoring of flame performance characteristics such as peak flame temperature.

Model : 105F1-1CG-020, 105F1-1CG-030, 105F1-1CG-040, 105F1-1CG-050, 105F1-1CG-060, 105F1-1CG-070,105F1-1CG-080, 105F1-1CG-090, 105F1-1CG-100, 105F1-1CGET-020, 105F1-1CGET-030, 105F1-1CGET-040, 105F1-1CGET-050, 105F1-1CGET-060, 105F1-1CGET-070, 105F1-1CGET-080, 105F1-1CGET-090, 105F1-1CGET-100.

Thiết bị phát hiện ngọn lửa 95DSS3 Fireye (95DSS3 Flame Scanner)

The Fireye^® InSight^® II Type 95DSS3 flame scanners are microprocessor based flame scanners utilizing solid state infrared (IR) and ultraviolet (UV) sensors.

The Fireye InSight II flame scanners incorporate two internal flame relays with adjustable ON/OFF thresholds and two 4-20 mA analog outputs, thereby eliminating the need for a remote flame amplifier.

The Fireye InSight II scanners are powered by 24 vdc and have electronic self-checking. Model 95DSS3-1 has one 8-pin and one 12-pin electrical cable quick disconnect. Models 95DSS3-1CEX and -1WICEX have internal terminal blocks for cable connection. The scanners have either an attached Keypad & VFD display, or an infrared transmitter for a remote handheld keypad/display.

Thiết bị phát hiện ngọn lửa 95IR-95UV-95DS Fireye ( 95IR_95UV_95DS Flame Scanners)

The Fireye^® InSight^® Type 95IR, 95UV, and 95DS flame scanners are microprocessor based flame scanners utilizing solid state infrared (IR), ultraviolet (UV) or dual (IR and UV) sensors. 

The Fireye InSight Type 95 flame scanners incorporate an internal flame relay with adjustable ON/OFF thresholds, thereby eliminating the need for a remote flame amplifier. All Fireye inSight scanner models are powered by 24 Vdc, have either a twelve-pin electrical quick disconnect or 10 ft. cable (“CG” models), and contain electronic self-checking (no mechanical shutter required). The scanners contain an eight character alpha-numeric LED display and a four push-button keypad to enable the user to view operating parameters and select setpoints.

Model : 95IR S1, 95UV S1, 95DS S1, 95IR S2, 95UV S2, 95DS S2

Thiết bị phát hiện ngọn lửa 65UV5 Fireye ( 65UV5 Flame Scanner)

The Fireye^® Simplicity™ 65UV5 self-checking scanners are used to detect ultraviolet emissions from fossil fuel flames such as natural gas, coke oven gas, propane, methane, butane, kerosene, light petroleum distillates and diesel fuels. 

The 65UV5 scanner is available with a one-second or four-second flame failure response time (FFRT) depending on the model selected. The “E” versions are one-second FFRT, the non ”E” versions are four seconds FFRT. The Fireye 65UV5-1004QD and 1004EQD flame scanners provide an analog 4 to 20 mA output referenced to flame signal strength.

Main Features:

• Fully integrated design - a true one-piece system
• No programming - minimal setup - ‘out of the box’ operation
• Superb detection, sensitivity and wide angle of view
• Proven and reliable technology
• Worldwide safety agency approvals
• Rugged NEMA 4X (IP66) housing
• Hazardous Area Classification

Model : 65UV5-1004, 65UV5-1004E, 65UV5-1004QD, 65UV5-1004EQD, 65UV5-1004ECEX

Thiết bị phát hiện ngọn lửa 85UVF-IRF Fireye (85UVF-IRFFlame Scanners)

The Fireye Phoenix Series 2 type 85UVF/IRF flame scanners are microprocessor based devices utilizing a solid state flame detection sensor. The Phoenix flame scanners incorporate an internal flame relay with automatically set ON/OFF thresholds, thereby eliminating the need for a remote flame amplifier or flame switch.

Phoenix scanners detect the amplitude of the modulations (the flame “flicker”) that occur within the targeted flame, over a wide frequency. During the scanner setup procedure, the amplitudes of the target flame are automatically stored by the flame scanner, together with optimum ON/OFF criteria. The appropriate sensor gain is automatically selected. Phoenix scanners incorporate full self-diagnostics and electronic self-checking.

Typical Applications

• Duct Burners
• Industrial Gas Burners
• Refinery Applications
• Low NOx Burners
• Waste Gas Units
• Incinerators

Model : 85UVF1A-1QD, 85UVF1-1CEX, 85UVF1-1CEX-K3, 85IRF1A-1QD, 85IRF1-1CEX, 85IRF1A-2QD, 85UVF1A-2QD, 85UVF1A-1QDK3, 85UVF1A-2QDK3, 85IRF4A-1QDWR, 85IRF4A-2QDWR, 85UVF4A-1QDWR, 85UVF4A-1QDK3WR, 85UVF4A-2QDWR, 85UVF4A-2QDK3WR

Thiết bị phát hiện ngọn lửa Fireye - Cảm biến ngọn lửa Fireye (InSight Series 4 Flame Scanner)

The InSight Series 4 scanners utilize advanced techniques for discrimination and integrate the flame detection, amplification, safety determination and flame switch functions into a single detection head. InSight Series 4 incorporates the superior detection and discrimination elements of the popular InSight II product with some enhanced features.

The scanner measures the amplitude of the modulations (the flame “flicker”) that occur within the targeted flame. During the scanner set-up procedure, the modulation frequency that yields the best flame ON/OFF discrimination is selected. The appropriate modulation frequency and sensor gain can be either manually or automatically selected.