Load capacity:

< 24 in [610 mm]/min:

> 24 in [610 mm]/min:

300 lbF [1.5 kN]

200 lbF [1 kN]

Speed range:

Standard:

Optional:

0.5 - 13 in/min [13 - 330 mm/min]

0.02 - 45 in/min [0.5 - 1,100 mm/min]

Maximum travel:

18.0 in [457 mm]

Speed setting accuracy:

±0.2%

Speed variation with load:

±0% [Stepper motor driven]

Travel accuracy:

±0.002 in per 10 in [±0.05 mm per 250 mm]

Travel resolution:

0.001 in [0.02 mm]

Travel display position retention:

Most recent position is recalled upon powering on

Limit switch repeatability:

±0.001 in [0.03 mm]

Power:

Universal input 80-240 VAC, 50/60 Hz, 60W

Weight:

56.5 lb [25.6 kg]

Function

Part No.

Description

Requirements

FollowMeTM

AF008

Crosshead movement responds to manually pushing or pulling on the force gauge shaft or load cell. Increasing force produces greater speeds. Ideal for setups and quick positioning.

• Series 7 or 5 gauge or indicator with load cell
• 09-1214 interface cable

Travel indication

AF009

Travel is indicated on the control unit display, with output via USB. The most recent position is displayed upon powering on. An internal scale utilizing Renishaw technology produces significantly higher accuracy than with conventional rotary encoder-based designs.

Backlash and nonlinearity are virtually eliminated.

• Field hardware installation required.
• If data output to a PC is required, add 09-1214 and 09-1158 cables, and a Series 7 or 5 gauge or indicator with load cell.

Computer control

AF010

The ESM303 may be fully controlled by a PC through a custom- written program in any language supporting ASCII communications. Also responds to the legacy Chatillon TCD command set and legacy Nexygen TCD software (not available from Mark-10).

This option is not required for MESUR™gauge Plus software.

• Series 7 or 5 gauge or indicator with load cell
• AF009 travel indication
• 09-1214 interface cable
• 09-1158 USB output cable
• For full speed range, consider AF017 and AF018 speed range extensions

Programmable travel limits

AF011

The stand stops at or cycles between programmable upper and lower travel distances.

- AF009 travel indication option

Overload protection

AF012

Protects a force gauge or force sensor against overload. Program the desired percentage of full scale of the gauge. Adjustable analog voltage setting allows the stand to interface with virtually any gauge with analog output.

• Series 7 or 5 gauge or indicator with load cell
• 09-1214 interface cable

Auto return

AF013

The crosshead moves to a limit switch, force set point, travel position, or break, then stops and reverses direction at full speed to the opposite limit.

• If reversing at force set point: Series 7 or 5 gauge or indicator with load cell, and 09-1214 interface cable
• If reversing at travel limit: AF011 programmable travel limits option
• If reversing at break: AF019 break detection op- tion and 09-1214 interface cable

Cycling / dwell time

AF014

Same as auto return, but with the ability to program up to 100,000 cycles. Programmable dwell time for upper and lower limits (set independently) can be set up for up to 10,000 seconds.

- Same as auto return, at the same speed in each direction. Add AF016 for independent up and down speeds.

Independent up and down speeds

AF016

Individually configure speeds for the up and down directions.

Low speed range extension

AF017

Extends the standard speed range down to

0.02 in/min (0.5 mm/min).

High speed range extension

AF018

Extends the standard speed range up to 45 in/min (1,100 mm/min).

Break detection

AF019

Crosshead stops at a sudden drop in force. Programmable percentage of peak force.

• Series 7 or 5 gauge or indicator with load cell
• 09-1214 interface cable

Load holding

AF020

Dynamically adjusts the crosshead position to maintain a programmed load for an indefinite or specified period of time.

• Series 7 or 5 gauge or indicator with load cell
• If a specified time is required, add AF014 cycling

/ dwell time option

• 09-1214 interface cable

Preload / sample touch

AF021

Stops the crosshead and/or zeroes the travel display at an initial preload - useful in tensile, compression, spring, elongation, and other applications. Preload is programmable as a percentage of force gauge/load cell full scale. Three modes: (1) stop, (2) stop and zero, and (3) zero without stopping.

• AF009 travel indication
• Series 7 or 5 gauge or indicator with load cell
• 09-1214 interface cable

Profiles

AF022

Save and recall sets of test parameters, such as speeds, travel limits, preloads, etc. Up to 50 profiles may be stored.

Complete options package

AFCOMP

Includes all functions listed above, plus 09-1214 interface cable and 09-1158 USB cable.

Requires a Series 7 or 5 gauge or indicator with load cell.

Hardware

ESM303

Motorized test stand,110V*

09-1214

Interface cable, gauge / indicator to ESM303

09-1158

USB output cable

AC1062

Load cell / indicator mounting kit

ESM303-001-1 / -2 / -3

Single column extension, 6 / 12 / 24 in. [150 / 300 / 600 mm]

ESM303-002-1 / -2 / -3

Double column extension, 6 / 12 / 24 in. [150 / 300 / 600 mm]

ESM303-003

Safety shield

Controller Options

AF008

FollowMeTM force-based manual positioning

AF009

Travel indication, with USB output

AF010

Computer control, via USB

AF011

Programmable travel limits

AF012

Integrated overload protection

AF013

Auto return

AF014

Cycling / dwell time

AF016

Independent up and down speeds

AF017

Extended speed range, low

AF018

Extended speed range, high

AF019

Break detection

AF020

Load holding

AF021

Preload / sample touch

AF022

Profiles

AFCOMP

Complete options package

(includes all Controller Options, plus 09-1124 and 09-1158 cables)