Teclock Vietnam | Đại lý Teclock chính hãng

Máy đo độ cứng cao su tự động GX 700 Teclock

SmartTester GX-700

---

New product! fully automatic type IRHD, M-method micro-sized international rubber hardness testerFully automatic IRHD a successful first domestic production. O-ring and the hardness of the rubber sheet can be measured.
By using the option of the plunger (the probe), you can measure with the durometer hardness test method A, E, E2, FO, 00 (approximate).
O-ring and hardness of small rubber parts and can be measured fully automatically.
It uses a voice coil motor to load system. Unlike the weight formula, it increased the friction and reproducibility of the internal mechanism.
A simple plug-in type, easy to exchange plunger (the probe). Becasue it's a domestic product, maintenance of correspondence is quick.
The sample stage is wide so that it allows the installation of various measurement jig.
It ca issue of calibration documents.

Mời quý khách hàng tham khảo thêm một số loại máy đo độ cứng tự động của hãng Teclock

GS 607 Teclock | Máy đo độ cứng cao su Teclock

Durometer Periodical Inspection

Durometer is a testing machine. In case that it corresponds to “Monitoring Machine ” and “Measuring Machine” of ISO 9001 (JIS G 9001), controlling machines along with it is needed. Teclock is one of a few manufacturers of durometer which has obtained the authentication of ISO 9001 and can originally issue 3 kinds of traceability system diagram, calibration certificate and inspection report that are needed for calibration documents. In addition, Teclock can issue 3 kinds of documents for durometer tester and indentor height gauge, that are needed for internal inspection. Use these for control based on internal calibration standard.

This is inspection machine which simply checks spring load value of analog type durometer. Putting defined load with 3 pieces of standard weight to the inverted durometer and inspecting whether graduation of 25, 50 and 75 correctly point out. Calibration certificate can be issued. (Digital type durometer and other makes products can not be calibrated.)

In addition, in the standard of overseas and also domestic, inspection method by using mechanism of even balance and with normal position of durometer is introduced.

GS 610 Teclock | Máy đo độ cứng nhựa Teclock

Thiết bị đo độ cứng GS 610 Teclock | Máy đo độ cứng cao su tự động Teclock

- Hardness can be measured by durometer with load and speed prescribed as standard only by operating switch.

- Varying in some degree of data measured by pushing by hand has been dramatically improved due to adopting stepping motor driving system.

- Alignment unit which realizes high contact between indentor (contact point) of durometer and test piece is mounted.

- 1kg can be measured by type A and type E durometer as they are. Measuring by type D needs optional weight ZY-128 for measuring 5kg.. Digital durometer GSD

GS 612 Teclock | Máy đo độ cứng của nhựa Teclock

Speed controller with high reliability is adopted for moving down speed adjustment unit.

- Alignment unit which realizes high contact between indenter (contact point) of durometer and test piece is mounted.

 - 65mm for analog and 40mm for digital are obtained for possible measuring range.

- Shaft with square thread is adopted that can prevent holder falling down and moving up and down.

- 1kg can be measured by type A and type E durometer as they are. Measuring by type D needs optional weight ZY-128 for measuring 5kg. Digital durometer GSD series needs optional weight ZY-090 for measuring 1kg.

- Calibration certificate of mass (with durometer) can be issued, which are prescribed in ISO / JIS.

GS 615 Teclock | Máy đo độ cứng cao su Teclock

Hardness can be measured by durometer with load prescribed by JIS by mounting durometer and manual operation.

   ● Adopting cam has realized easy operation and cost performance.

   ● Alignment unit which realizes high contact between indenter (contact point) of durometer and test piece is mounted.

   ● 1kg can be measured by type A and type E durometer.as they are. Measuring by type D needs optional weight ZY-128 for measuring 5kg.. Digital durometer GSD series needs optional weight ZY-079 for measuring 1kg..

   ● Calibration certificate can be issued (Operation speed certificate can not be issued.)

GS 608Sel Teclock | Máy đo độ cứng cao su Teclock

Totally Automatic type IRHD/M method Micro–Size International Rubber Hardness Tester

Micro-hardness can be measured by 1/8 scale each durometer of type A, E, E2, OO, FO in addition to IRHD / M method.

     ● Hardness of O ring and small rubber parts can be measured with totally automatic.

     ● Voice coil motor is adopted for load system. Friction and reproducibility of inner mechanism is improved, which is different from weight system.

     ● It is plug-in type that plunger (contact point) can be easily changed and recalibration on test method change is not needed.

     ● As test piece table is wide, various measuring jigs can be set up.

Xem thêm chi tiết : TẠI ĐÂY